Do you want to switch to Do you want to switch to
Item was added to your basket
Model Number: LPS2 1512-100 SE
SKU: CL2204
Peak: 2600 W
Power: 1500 W
60 Seconds: 270 A
Continously: 180 A
Capacity: 1320 Wh (100 Ah)
Efficient energy: 1 kWh
Alternator: 300 W
Mains: 550 W
12V DC can be turned ON/OFF from the front of the LPS. If pressing OK the LPS will enter the main menu. From the main menu it is possible to find data for DC charging and 12V DC output.
230 VAC can be turned ON/OFF from the front of the LPS. If pressing OK the LPS will enter the main menu. From the main menu it is possible to find data for AC charging and 230 VAC output.
The RCBO relay is included in the LPS. In case of overload, it will shut down for the 230V AC output. The RCBO relay is also a fault current circuit breaker.
In front of the LPS it is possible to e.g., connect 230V equipment or an extension cord.
12V DC appliances can be connected to the output terminals.
The LPS is charged from any alternator via the 12 or 24V DC input. The DC IN shall be connected to the starter battery. The built-in booster will raise the voltage and at the same time also protect the starter battery.
For charging from solar panels, they shall also be connected to DC -IN or for DC OUT (and C2).
There is an M12 connection for the remote control. The remote control can be used for turning on/off the LPS.
The M12 data connection is for upload of software updates, change of parameters or withdrawal of data from the LPS via a can modem.
C1: For charging from the vehicle, it is required to connect C1 to D+ or the ignition key.
C2: N/A
The grey Neutrik connector is included for 230V AC output.
The blue Neutrik connector is for 230V AC input. The charging cable with the blue Neutrik is shipped together with LPS II.
Vibration and safety tested for leisure, industrial and automotive use.
RoHS Directive 2011/65/EU, Low Voltage Directive 2014/35/EU, EMC 2014/30/EU, E-Marking
Redesign of all functionalities for making the LPS unit as ultra compact as possible. The high-voltage AC inverter has an impressive 94% efficiency at 1000 W and high peak performance for start-up of heavy-duty loads.
All boards within Clayton Power's LPS are coated to ensure maximum functionality even in challenging environments. The inverter, charger, solar regulator, and DC booster have been redesigned to make the product as compact and efficient as possible.
High-end and compact LiFePO4 battery cells with high energy density and long lifetime.
| SKU No. | CL2204 | |
| Battery type | Li-Ion 12V – 100Ah | |
| Battery chemistry | LiFePO4 | |
| Battery capacity | 100Ah (1320Wh) | |
| Battery available capacity | 80Ah (1050Wh) | |
| AC Input voltage | 207 VAC – 253 VAC | |
| AC input frequency | 45 Hz – 65 Hz | |
| AC Input power (Charge power) | 550 W | |
| AC Output voltage +- 10% | 230 VAC pure sine wave | |
| AC Output frequency | 50 Hz | |
| AC output power – Continuously (ambient temp) | 1300 W | |
| AC output power - 10 min. | 1500 W | |
| AC output power - Peak | 2600 W | |
| AC output power - AC In connected | 2600 W | |
| AC output efficiency (1000W) | 94% | |
| DC Input voltage | 11,5 - 32 VDC | |
| DC input current | 25 A | |
| DC output voltage | 10-14,4 VDC | |
| DC output charge current – Continuously | 90 A | |
| DC output discharge current – Continuously | 180 A | |
| DC output discharge current – 1 min. | 270 A | |
| Input signals (5) | C1, C2, M12 x 3 | |
| Output signals (4) | C2 & M12 x 3 | |
| Self-discharge rate per month | < 5% | |
| Self consumption - Operating mode, Only DC Output active | < 1 W | |
| Self consumption - Operating mode, inverter and DC Output in with > 50W | 20 W | |
| Connection 230VAC | Neutrik and Schuko | |
| Connection C1 / C2 | M4 | |
| Connection DC input | M8 | |
| Connection DC output | M8 | |
| Cooling | Forced air (fan) | |
| Operating temperature (output will be limited below 0°C and ab) | -20°C~50°C | |
| IP rating | IP21 | |
| Product weight | 22,5 kg | |
| Product dimensions (HxWxL) | 256x277x409mm | |
| Jumpstart | 40 A / 5 min |